Go to the documentation of this file.
    1 
    2 /*
    3  * ====================== WARNING ======================
    4  *
    5  * THE CONTENTS OF THIS FILE HAVE BEEN AUTO-GENERATED.
    6  * DO NOT MODIFY IN ANY WAY.
    7  *
    8  * ====================== WARNING ======================
    9  */
   10 /**
   11  * @file le_ulpm_common.h
   12  *
   13  * Type definitions for le_ulpm.
   14  *
   15  */
   16 #ifndef LE_ULPM_COMMON_H_INCLUDE_GUARD
   17 #define LE_ULPM_COMMON_H_INCLUDE_GUARD
   18 
   19 
   20 #include "legato.h"
   21 
   22 #define IFGEN_LE_ULPM_PROTOCOL_ID "9431e37e61d607aea62e91937079db61"
   23 #define IFGEN_LE_ULPM_MSG_SIZE 32
   24 /** @addtogroup le_ulpm
   25  *  @{ **/
   26 
   27 
   28 //--------------------------------------------------------------------------------------------------
   29 /**
   30  * Maximum version length of mcu firmware.
   31  */
   32 //--------------------------------------------------------------------------------------------------
   33 #define LE_ULPM_MAX_VERS_LEN 8
   34 
   35 //--------------------------------------------------------------------------------------------------
   36 /**
   37  * State of gpio pin. This state will be used to exit from low power state.
   38  */
   39 //--------------------------------------------------------------------------------------------------
   40 typedef enum
   41 {
   42     LE_ULPM_GPIO_LOW = 0,
   43         ///< Gpio voltage level low.
   44     LE_ULPM_GPIO_HIGH = 1,
   45         ///< Gpio voltage level high.
   46     LE_ULPM_GPIO_RISING = 2,
   47         ///< Gpio edge rising.
   48     LE_ULPM_GPIO_FALLING = 3,
   49         ///< Gpio edge falling.
   50     LE_ULPM_GPIO_BOTH = 4,
   51         ///< Gpio edge either rising or falling.
   52     LE_ULPM_GPIO_OFF = 5
   53         ///< Gpio off.
   54 }
   55 le_ulpm_GpioState_t;
   56 
   57 
   58 //--------------------------------------------------------------------------------------------------
   59 /**
   60  * Possible ULPS (Ultra Low Power State) configurations to select before shutdown.
   61  *
   62  * Value 3 is skipped as it should not be used according to swimcu_pm documentation.
   63  */
   64 //--------------------------------------------------------------------------------------------------
   65 typedef enum
   66 {
   67     LE_ULPM_DISABLE_PSM = 0,
   68         ///< Resquest to disable PSM
   69     LE_ULPM_PSM_WITH_ULPM_FALLBACK = 1,
   70         ///< Request enable PSM with ULPM fallback
   71     LE_ULPM_POWER_OFF = 2,
   72         ///< Request power off module
   73     LE_ULPM_NO_REQUEST = 4,
   74         ///< No request (Default value)
   75     LE_ULPM_PSM_ONLY = 5,
   76         ///< Request enable PSM only
   77     LE_ULPM_ULPM_ONLY = 6
   78         ///< Request enable ULPM only
   79 }
   80 le_ulpm_ULPSConfiguration_t;
   81 
   82 
   83 
   84 //--------------------------------------------------------------------------------------------------
   85 /**
   86  * Get if this client bound locally.
   87  */
   88 //--------------------------------------------------------------------------------------------------
   89 LE_SHARED bool ifgen_le_ulpm_HasLocalBinding
   90 (
   91     void
   92 );
   93 
   94 
   95 //--------------------------------------------------------------------------------------------------
   96 /**
   97  * Init data that is common across all threads
   98  */
   99 //--------------------------------------------------------------------------------------------------
  100 LE_SHARED void ifgen_le_ulpm_InitCommonData
  101 (
  102     void
  103 );
  104 
  105 
  106 //--------------------------------------------------------------------------------------------------
  107 /**
  108  * Perform common initialization and open a session
  109  */
  110 //--------------------------------------------------------------------------------------------------
  111 LE_SHARED le_result_t ifgen_le_ulpm_OpenSession
  112 (
  113     le_msg_SessionRef_t _ifgen_sessionRef,
  114     bool isBlocking
  115 );
  116 
  117 //--------------------------------------------------------------------------------------------------
  118 /**
  119  * Configure the system to boot based on a state change of a given GPIO.
  120  *
  121  * @return
  122  *      - LE_OK if specified gpio is configured as boot source.
  123  *      - LE_NOT_PERMITTED if the process lacks sufficient permissions to configure the GPIO as a
  124  *        boot source.
  125  *      - LE_UNSUPPORTED if the device lacks the ability to boot based on the given GPIO.
  126  *      - LE_BAD_PARAMETER if the state parameter was rejected.
  127  *      - LE_FAULT if there is a non-specific failure.
  128  */
  129 //--------------------------------------------------------------------------------------------------
  130 LE_SHARED le_result_t ifgen_le_ulpm_BootOnGpio
  131 (
  132     le_msg_SessionRef_t _ifgen_sessionRef,
  133         uint32_t gpioNum,
  134         ///< [IN] Gpio number to boot.
  135         le_ulpm_GpioState_t state
  136         ///< [IN] State which should cause boot.
  137 );
  138 
  139 //--------------------------------------------------------------------------------------------------
  140 /**
  141  * Boot after expiration of timer interval.
  142  *
  143  * @return
  144  *      - LE_OK if timer is configured as boot source.
  145  *      - LE_NOT_PERMITTED if the process lacks sufficient permissions to configure the timer as a
  146  *        boot source.
  147  *      - LE_UNSUPPORTED if the device lacks the ability to boot based on a timer.
  148  *      - LE_BAD_PARAMETER if the state parameter was rejected.
  149  *      - LE_FAULT if there is a non-specific failure.
  150  */
  151 //--------------------------------------------------------------------------------------------------
  152 LE_SHARED le_result_t ifgen_le_ulpm_BootOnTimer
  153 (
  154     le_msg_SessionRef_t _ifgen_sessionRef,
  155         uint32_t expiryVal
  156         ///< [IN] Expiration time(in second) to boot. This is relative time from
  157         ///< modem/app processor shutdown.
  158 );
  159 
  160 //--------------------------------------------------------------------------------------------------
  161 /**
  162  * Configure and enable an ADC as a boot source.
  163  *
  164  * It is possible to specify a single range of operation or two ranges of operation with a
  165  * non-operational range in between.  When bootAboveAdcReading is less than bootBelowAdcReading,
  166  * then a single range bootAboveReading to bootBelowReading is the configured operational range.
  167  * However if bootAboveAdcReading is greater than bootBelowAdcReading, then there are two
  168  * operational ranges.  The first is any reading less than bootBelowAdcReading and the second is any
  169  * reading greater than bootAboveAdcReading.
  170  *
  171  * @return
  172  *      - LE_OK on success
  173  *      - LE_NOT_PERMITTED if the process lacks sufficient permissions to configure the adc as a
  174  *        boot source.
  175  *      - LE_OVERFLOW if the provided bootAboveAdcReading or bootBelowAdcReading are too large to
  176  *        convert to fit in the internal string buffer.
  177  *      - LE_BAD_PARAMETER if the pollIntervalInMs, bootAboveAdcReading or bootBelowAdcReading
  178  *        parameter were rejected.
  179  *      - LE_UNSUPPORTED if the device does not support using the given adc as a boot source.
  180  *      - LE_FAULT if there is a non-specific failure.
  181  */
  182 //--------------------------------------------------------------------------------------------------
  183 LE_SHARED le_result_t ifgen_le_ulpm_BootOnAdc
  184 (
  185     le_msg_SessionRef_t _ifgen_sessionRef,
  186         uint32_t adcNum,
  187         ///< [IN] Number of the ADC to configure
  188         uint32_t pollIntervalInMs,
  189         ///< [IN] How frequently to poll the ADC while sleeping
  190         double bootAboveAdcReading,
  191         ///< [IN] Reading above which the system should boot
  192         double bootBelowAdcReading
  193         ///< [IN] Reading below which the system should boot
  194 );
  195 
  196 //--------------------------------------------------------------------------------------------------
  197 /**
  198  * Get the ultra low power manager firmware version.
  199  *
  200  * @return
  201  *      - LE_OK on success
  202  *      - LE_OVERFLOW if version string to big to fit in provided buffer
  203  *      - LE_FAULT for any other errors
  204  */
  205 //--------------------------------------------------------------------------------------------------
  206 LE_SHARED le_result_t ifgen_le_ulpm_GetFirmwareVersion
  207 (
  208     le_msg_SessionRef_t _ifgen_sessionRef,
  209         char* version,
  210         ///< [OUT] Firmware version string
  211         size_t versionSize
  212         ///< [IN]
  213 );
  214 
  215 //--------------------------------------------------------------------------------------------------
  216 /**
  217  * Initiate shutting down of app processor/modem etc.
  218  *
  219  * @return
  220  *      - LE_OK if entry to ultra low power mode initiates properly.
  221  *      - LE_UNAVAILABLE if shutting is not possible now. Try again.
  222  *      - LE_NOT_PERMITTED if the process lacks sufficient permissions to perform a shutdown.
  223  *      - LE_UNSUPPORTED if the device lacks the ability to shutdown via ULPM.
  224  *      - LE_FAULT if there is a non-specific failure.
  225  */
  226 //--------------------------------------------------------------------------------------------------
  227 LE_SHARED le_result_t ifgen_le_ulpm_ShutDown
  228 (
  229     le_msg_SessionRef_t _ifgen_sessionRef
  230 );
  231 
  232 //--------------------------------------------------------------------------------------------------
  233 /**
  234  * Initiate reboot of app processor/modem etc.
  235  *
  236  * @return
  237  *      - LE_OK if reboot initiates properly.
  238  *      - LE_UNAVAILABLE if rebooting is not possible now. Try again.
  239  *      - LE_NOT_PERMITTED if the process lacks sufficient permissions to perform a reboot.
  240  *      - LE_UNSUPPORTED if the device lacks the ability to reboot via ULPM.
  241  *      - LE_FAULT if there is a non-specific failure.
  242  */
  243 //--------------------------------------------------------------------------------------------------
  244 LE_SHARED le_result_t ifgen_le_ulpm_Reboot
  245 (
  246     le_msg_SessionRef_t _ifgen_sessionRef
  247 );
  248 
  249 //--------------------------------------------------------------------------------------------------
  250 /**
  251  * Set the Low Power Mode configuration to apply when le_ulpm_ShutDown is called.
  252  *
  253  * @return
  254  *      - LE_OK on success
  255  *      - LE_BAD_PARAMETER if the value of a parameter is invalid
  256  *      - LE_UNSUPPORTED if not supported
  257  *      - LE_FAULT for any other errors
  258  */
  259 //--------------------------------------------------------------------------------------------------
  260 LE_SHARED le_result_t ifgen_le_ulpm_SetShutDownStrategy
  261 (
  262     le_msg_SessionRef_t _ifgen_sessionRef,
  263         le_ulpm_ULPSConfiguration_t ulpsConfig
  264         ///< [IN] Value used to configure ULPS.
  265 );
  266 /** @} **/
  267 #endif // LE_ULPM_COMMON_H_INCLUDE_GUARD
LE_ULPM_GPIO_FALLING
Gpio edge falling. 
Definition: le_ulpm_common.h:48
LE_ULPM_GPIO_LOW
Gpio voltage level low. 
Definition: le_ulpm_common.h:42
LE_ULPM_GPIO_RISING
Gpio edge rising. 
Definition: le_ulpm_common.h:46
LE_SHARED
#define LE_SHARED
Definition: le_basics.h:287
le_result_t
le_result_t
Definition: le_basics.h:46
LE_ULPM_GPIO_HIGH
Gpio voltage level high. 
Definition: le_ulpm_common.h:44
LE_ULPM_PSM_WITH_ULPM_FALLBACK
Request enable PSM with ULPM fallback. 
Definition: le_ulpm_common.h:69
le_ulpm_GpioState_t
le_ulpm_GpioState_t
Definition: le_ulpm_common.h:40
LE_ULPM_POWER_OFF
Request power off module. 
Definition: le_ulpm_common.h:71
LE_ULPM_NO_REQUEST
No request (Default value) 
Definition: le_ulpm_common.h:73
le_msg_SessionRef_t
struct le_msg_Session * le_msg_SessionRef_t
Definition: le_messaging.h:860
legato.h
LE_ULPM_PSM_ONLY
Request enable PSM only. 
Definition: le_ulpm_common.h:75
LE_ULPM_GPIO_BOTH
Gpio edge either rising or falling. 
Definition: le_ulpm_common.h:50
LE_ULPM_ULPM_ONLY
Request enable ULPM only. 
Definition: le_ulpm_common.h:77
LE_ULPM_DISABLE_PSM
Resquest to disable PSM. 
Definition: le_ulpm_common.h:67
le_ulpm_ULPSConfiguration_t
le_ulpm_ULPSConfiguration_t
Definition: le_ulpm_common.h:65
LE_ULPM_GPIO_OFF
Gpio off. 
Definition: le_ulpm_common.h:52